|
0 |
PLEASE TURN OFF POWER |
|
1 |
TH PARITY ALARM |
|
2 |
TV PARITY ALARM |
|
3 |
TOO MANY DIGITS |
|
4 |
ADDRESS NOT FOUND |
|
5 |
NO DATA AFTER ADDRESS |
|
6 |
ILLEGAL USE OF NEGATIVE SIGN |
|
7 |
ILLEGAL USE OF DECIMAL POINT |
|
9 |
ILLEGAL ADDRESS INPUT |
|
10 |
IMPROPER G–CODE |
|
11 |
NO FEEDRATE COMMANDED |
|
14 |
CAN NOT COMMAND G95 (M series) |
|
14 |
ILLEGAL LEAD COMMAND (T series) |
|
15 |
TOO MANY AXES COMMANDED (M series) |
|
15 |
TOO MANY AXES COMMANDED (T series) |
|
20 |
OVER TOLERANCE OF RADIUS |
|
21 |
ILLEGAL PLANE AXIS COMMANDED |
|
22 |
NO CIRCLE RADIUS |
|
23 |
ILLEGAL RADIUS COMMAND (T series) |
|
25 |
CANNOT COMMAND F0 IN G02/G03 (M series) |
|
27 |
NO AXES COMMANDED IN G43/G44 (M series) |
|
28 |
ILLEGAL PLANE SELECT |
|
29 |
ILLEGAL OFFSET VALUE (M series) |
|
29 |
ILLEGAL OFFSET VALUE (T series) |
|
30 |
ILLEGAL OFFSET NUMBER (M series) |
|
30 |
ILLEGAL OFFSET NUMBER (T series) |
|
31 |
ILLEGAL P COMMAND IN G10 |
|
32 |
ILLEGAL OFFSET VALUE IN G10 |
|
33 |
NO SOLUTION AT CRC (M series) |
|
33 |
NO SOLUTION AT CRC (T series) |
|
34 |
NO CIRC ALLOWED IN ST–UP /EXT BLK (M series) |
|
34 |
NO CIRC ALLOWED IN ST–UP /EXT BLK (T series) |
|
35 |
CAN NOT COMMANDED G31 (T series) |
|
35 |
CAN NOT COMMANDED G39 (M series) |
|
36 |
CAN NOT COMMANDED G31 (M series) |
|
37 |
CAN NOT CHANGE PLANE IN CRC (M seires) |
|
37 |
CAN NOT CHANGE PLANE IN NRC (T seires) |
|
38 |
INTERFERENCE IN CIRCULAR BLOCK (M seires) |
|
38 |
INTERFERENCE IN CIRCULAR BLOCK (T series) |
|
39 |
CHF/CNR NOT ALLOWED IN NRC (T series) |
|
40 |
INTERFERENCE IN G90/G94 BLOCK (T series) |
|
41 |
INTERFERENCE IN CRC (M seires) |
|
41 |
INTERFERENCE IN NRC (T seires) |
|
42 |
G45/G48 NOT ALLOWED IN CRC (M series) |
|
44 |
G27–G30 NOT ALLOWED IN FIXED CYC (M series) |
|
45 |
ADDRESS Q NOT FOUND (G73/G83) (M series) |
|
46 |
ILLEGAL REFERENCE RETURN COMMAND |
|
47 |
ILLEGAL AXIS SELECT |
|
48 |
BASIC 3 AXIS NOT FOUND |
|
49 |
ILLEGAL OPERATION (G68/G69) (M series) |
|
50 |
CHF/CNR NOT ALLOWED IN THRD BLK (M series) |
|
50 |
CHF/CNR NOT ALLOWED IN THRD BLK(T series) |
|
51 |
MISSING MOVE AFTER CHF/CNR (M series) |
|
51 |
MISSING MOVE AFTER CHF/CNR (T series) |
|
52 |
CODE IS NOT G01 AFTER CHF/CNR (M series) |
|
52 |
CODE IS NOT G01 AFTER CHF/CNR (T series) |
|
53 |
TOO MANY ADDRESS COMMANDS (M series) |
|
53 |
TOO MANY ADDRESS COMMANDS (T seires) |
|
54 |
NO TAPER ALLOWED AFTER CHF/CNR (T series) |
|
55 |
MISSING MOVE VALUE IN CHF/CNR (M series) |
|
55 |
MISSING MOVE VALUE IN CHF/CNR (T series) |
|
56 |
NO END POINT & ANGLE IN CHF/CNR (T series) |
|
57 |
NO SOLUTION OF BLOCK END (T series) |
|
58 |
END POINT NOT FOUND (M series) |
|
58 |
END POINT NOT FOUND (T series) |
|
59 |
PROGRAM NUMBER NOT FOUND |
|
60 |
SEQUENCE NUMBER NOT FOUND |
|
61 |
ADDRESS P/Q NOT FOUND IN G70–G73 (T series) |
|
62 |
ILLEGAL COMMAND IN G71–G76 (T series) |
|
63 |
SEQUENCE NUMBER NOT FOUND (T series) |
|
64 |
SHAPE PROGRAM NOT MONOTONOUSLY (T series) |
|
65 |
ILLEGAL COMMAND IN G71–G73 (T series) |
|
66 |
IMPROPER G–CODE IN G71–G73 (T series) |
|
67 |
CAN NOT ERROR IN MDI MODE (T series) |
|
69 |
FORMAT ERROR IN G70–G73 (T series) |
|
70 |
NO PROGRAM SPACE IN MEMORY |
|
71 |
DATA NOT FOUND |
|
72 |
TOO MANY PROGRAMS |
|
73 |
PROGRAM NUMBER ALREADY IN |
|
74 |
ILLEGAL PROGRAM NUMBER |
|
75 |
PROTECT |
|
76 |
ADDRESS P NOT DEFINED |
|
77 |
SUB PROGRAM NESTING ERROR |
|
78 |
NUMBER NOT FOUND |
|
79 |
PROGRAM VERIFY ERROR |
|
80 |
G37 ARRIVAL SIGNAL NOT ASSERTED (M series) |
|
80 |
G37 ARRIVAL SIGNAL NOT ASSERTED (T series) |
|
81 |
OFFSET NUMBER NOT FOUND IN G37 (M series) |
|
81 |
OFFSET NUMBER NOT FOUND IN G37 (T series) |
|
82 |
H–CODE NOT ALLOWED IN G37 (M series) |
|
82 |
T–CODE NOT ALLOWED IN G37 (T series) |
|
83 |
ILLEGAL AXIS COMMAND IN G37 (M series) |
|
83 |
ILLEGAL AXIS COMMAND IN G37 (T series) |
|
85 |
COMMUNICATION ERROR |
|
86 |
DR SIGNAL OFF |
|
87 |
BUFFER OVERFLOW |
|
88 |
LAN FILE TRANS ERROR (CHANNEL–1) |
|
89 |
LAN FILE TRANS ERROR (CHANNEL–2) |
|
90 |
REFERENCE RETURN INCOMPLETE |
|
91 |
REFERENCE RETURN INCOMPLETE |
|
92 |
AXES NOT ON THE REFERENCE POINT |
|
94 |
P TYPE NOT ALLOWED (COORD CHG) |
|
95 |
P TYPE NOT ALLOWED (EXT OFS CHG) |
|
96 |
P TYPE NOT ALLOWED (WRK OFS CHG) |
|
97 |
P TYPE NOT ALLOWED (AUTO EXEC) |
|
98 |
G28 FOUND IN SEQUENCE RETURN |
|
99 |
MDI EXEC NOT ALLOWED AFT. SEARCH |
|
100 |
PARAMETER WRITE ENABLE |
|
101 |
PLEASE CLEAR MEMORY |
|
109 |
FORMAT ERROR IN G08 (M series) |
|
110 |
DATA OVERFLOW |
|
111 |
CALCULATED DATA OVERFLOW |
|
112 |
DIVIDED BY ZERO |
|
113 |
IMPROPER COMMAND |
|
114 |
FORMAT ERROR IN MACRO |
|
115 |
ILLEGAL VARIABLE NUMBER |
|
116 |
WRITE PROTECTED VARIABLE |
|
118 |
PARENTHESIS NESTING ERROR |
|
119 |
ILLEGAL ARGUMENT |
|
122 |
FOUR FOLD MACRO MODAL–CALL |
|
123 |
CAN NOT USE MACRO COMMAND IN DNC |
|
124 |
MISSING END STATEMENT |
|
125 |
FORMAT ERROR IN MACRO |
|
126 |
ILLEGAL LOOP NUMBER |
|
127 |
NC, MACRO STATEMENT IN SAME BLOCK |
|
128 |
ILLEGAL MACRO SEQUENCE NUMBER |
|
129 |
ILLEGAL ARGUMENT ADDRESS |
|
130 |
ILLEGAL AXIS OPERATION |
|
131 |
TOO MANY EXTERNAL ALARM MESSAGES |
|
132 |
ALARM NUMBER NOT FOUND |
|
133 |
ILLEGAL DATA IN EXT. ALARM MSG |
|
135 |
ILLEGAL ANGLE COMMAND (M series) |
|
135 |
SPINDLE ORIENTATION PLEASE (T series) |
|
136 |
C/H–CODE & MOVE CMD IN SAME BLK. (T series) |
|
136 |
ILLEGAL AXIS COMMAND (M series) |
|
137 |
M–CODE & MOVE CMD IN SAME BLK. |
|
138 |
SUPERIMPOSED DATA OVERFLOW |
|
139 |
CAN NOT CHANGE PMC CONTROL AXIS |
|
141 |
CAN NOT COMMAND G51 IN CRC (M series) |
|
142 |
ILLEGAL SCALE RATE (M series) |
|
143 |
SCALED MOTION DATA OVERFLOW (M series) |
|
144 |
ILLEGAL PLANE SELECTED (M series) |
|
145 |
ILLEGAL CONDITIONS IN POLAR COORDINATE INTERPOLATION |
|
146 |
IMPROPER G CODE |
|
148 |
ILLEGAL SETTING DATA (M series) |
|
149 |
FORMAT ERROR IN G10L3 (M series) |
|
150 |
ILLEGAL TOOL GROUP NUMBER |
|
151 |
TOOL GROUP NUMBER NOT FOUND |
|
152 |
NO SPACE FOR TOOL ENTRY |
|
153 |
T–CODE NOT FOUND |
|
154 |
NOT USING TOOL IN LIFE GROUP (M series) |
|
155 |
ILLEGAL T–CODE IN M06 (M series) |
|
155 |
ILLEGAL T–CODE IN M06 (T series) |
|
156 |
P/L COMMAND NOT FOUND |
|
157 |
TOO MANY TOOL GROUPS |
|
158 |
ILLEGAL TOOL LIFE DATA |
|
159 |
TOOL DATA SETTING INCOMPLETE |
|
163 |
COMMAND G68/G69 INDEPENDENTLY T series (At two–path) |
|
175 |
ILLEGAL G107 COMMAND |
|
176 |
IMPROPER G–CODE IN G107 (M series) |
|
176 |
IMPROPER G–CODE IN G107 (T series) |
|
177 |
CHECK SUM ERROR (G05 MODE) |
|
178 |
G05 COMMANDED IN G41/G42 MODE |
|
179 |
PARAM. (NO. 7510) SETTING ERROR |
|
180 |
COMMUNICATION ERROR (REMOTE BUF) |
|
181 |
FORMAT ERROR IN G81 BLOCK (Hobbing machine, EGB) (M series) |
|
182 |
G81 NOT COMMANDED (Hobbing machine) (M series) |
|
183 |
DUPLICATE G83 (COMMANDS) (Hobbing machine) (M series) |
|
184 |
ILLEGAL COMMAND IN G81 (Hobbing machine, EGB) (M series) |
|
185 |
RETURN TO REFERENCE POINT (Hobbing machine) (M series) |
|
186 |
PARAMETER SETTING ERROR (Hobbing machine, EGB) (M series) |
|
187 |
HOB COMMAND IS NOT ALLOWED |
|
190 |
ILLEGAL AXIS SELECT (M series) |
|
194 |
SPINDLE COMMAND IN SYNCHRO–MODE |
|
195 |
MODE CHANGE ERROR |
|
197 |
C–AXIS COMMANDED IN SPINDLE MODE |
|
199 |
MACRO WORD UNDEFINED |